Search results

not sure the pinout on the 17 rzr gauge connector changed i would have to look. i would check the green and yellow wires at the gauge plug those are the canbus to stream engine data.

yes x2

1917 was 3rd to cross of utvs.

heard a lot of chatter bout pit speed penalties

brian b 1911 started 24th he may get podium on time???

radio chatter said 1905 got hit and is on fire????

you can expand class 1900 and see everything and where they are at

http://irctracking.com/2014/Vegas-Reno/

bottom rails are 65" wide. with where my seats ended up i could have made this a little shorter but too late know :-)) sorry i have been neglecting my project. i did get the rotax motor in and all lined up but not much since that. i have alot of parts coming in and hope to get back on it very...

had some time to finish up the motor harness. not much to look at as all the fun stuff is in the body harness. injectors and trans sensors are labeled for easy install. body harness should be done by end of next week.

Plug and play wiring kits are in the works for your rotax / rhino swaps. I want to hear from everyone, if you have already done one or are thinking about it. What do you wish you did or what would you like a wiring kit to have. Everything from bells and whistles to where do you want to mount...

rotax is here :D:D:D:D new progress to made this weekend. pics to come soon.

finally made a deal for an 08 canam 800. should have it in a week or so. :D:D:D

there seems to be less and less of the rhino left. i figured if i am going this far why not go further and further make it better .....stronger.....cooler. i look forward to input and to making more progress. thank you to all who have helped.

im also looking for a rotax if anyone has one they want to get ride of.

more progress :)

i will get some pics up for you guys today. i have a build thread started and will be updating that as well. thank you guys for all your input it really does help!!

why didn't you like it 60" wide???

thank you for the offer but i have an empyre wide body kit already. and yes i lowered my dash. top of hood/dash is 26" off the floor. did you say your roof is at 40" off the floor?? im kinda tall and round :) so i wanted a little more head room and a taller roof height to get my beer belly over...

i am dropping the seats all the way down and needed to make it that wide to fit them.

i have been making lots of progress on my build, pics will be up soon. some friends that have come checked it say it looks to wide??? give me your input on my dimensions please??? a pilar and roof width 59" door bar width 71" bottom of frame width 64" from floor to roof 50"

i have two sheets of .076 here so i will use as much of that on the body panels. not sure on the skid plates yet most likely 1/4 as a minimum.

thank you all for the input. :D

what thickness of alloy should i use for skid plates, side panels, roof and firewalls etc etc??? oh this is for a desert race rhino. i saw a post somewhere but now i cant find it. thank you in advance.

more pics

went backwards a little and now some forward progress. lots more to do, give me your input.

yes i plan on boxing in all those area's and plating all the pivot point's.

i have an empyre wide boby kit and yes i did also get the top dash piece. i am thinking of using it just so the hood and all looks right but i am not going to use the stock plastic dash. i may wind up building a whole new dash from scratch but not sure yet. i am dropping the dash at least 4"...

i am doing some more planning and mock up and i had a questions. i am dropping the dash like 4 inches. but i also noticed that it looks like to me i should also bring the dash rearward??? with the dropped seats and i plan to move them as far back as i can. what do you guys think???

thanks for the input joey, i will give that some thought. hey while i got you, can you let me know what your door bar height is and roof height is???

here are a few pics of the start i have. i hope by the end of the weekend to have a lot more done. feedback good and bad welcomed.

magnum builds nice stuff plan and simple. but in this economy i cant afford them :-) i am going to do all the work myself with some help from my best welder buddy. i cant wait to get started on it, i haven't have a good build in years. the last project i did was a ground up custom chopper that...

yes i have already been giving that stuff some thought. i am also planning on building a custom dash to help with all of that. as far as wiring goes i have been doing 12volt wiring for 15 years and have wired many on and off road vehicles from scratch. if you wanna bring your rhino over to...

hello all i am in the beginning stages of chopping and dropping my rhino. i bought the rhino with the intention of doing this. i have been reading as much as my mind will take and i have 100's of pics of previous projects that i have found on this and other forums. i have the rhino all chopped...